您好,欢迎光临莱州聚峰机械有限公司网站! 郑重声明 购机 售后 聚峰官微

全国咨询热线

400-879-1999

您的位置: 首页 > 新闻资讯 > 行业新闻
搅拌车的系统压力不够如何处理呢?
来源:https://www.cnzkjf.com/ 日期:2020-09-07
  在混凝土搅拌车使用过程中,如果液压系统出现故障会使搅拌车的工作性能大大降低,车主朋友们只有了解了液压系统的故障原因并及时排出故障才能使搅拌车恢复正常,今天收集了有关搅拌车液压系统压力不足或完全无压力的原因、诊断和排除,供车主朋友们参考学习。
  In the process of using the concrete mixer, if the hydraulic system fails, the working performance of the mixer will be greatly reduced. Only when the owners understand the fault causes of the hydraulic system and timely eliminate and solve the fault, can the mixer return to normal. Today, we collected the causes, diagnosis and troubleshooting of the hydraulic system of the mixer truck for the owner's friends We refer to learning.
  如果混凝土搅拌车出现液压系统压力不足或完全无压力时,我们可以根据以下几个方面依次进行排查:
  If there is insufficient or no pressure in the hydraulic system of the concrete mixer truck, we can check it according to the following aspects:
  查看液压泵是否能输出液压油。如果是新的液压泵,无液压油输出,可能是泵体有铸造缺陷(缩孔、砂眼等),使吸油腔和压油腔相通,失去压油能力,应及时找厂家更换。若不是新的液压泵,无液压油输出,则可能是泵的转向不对,零件磨损严重或损坏,及时更换。
  Check whether the hydraulic pump can output hydraulic oil. If it is a new hydraulic pump without hydraulic oil output, it may be that the pump body has casting defects (shrinkage cavity, sand hole, etc.), so that the oil suction chamber and the pressure oil chamber are connected, and the oil pressure capacity is lost, it should be replaced by the manufacturer in time. If it is not a new hydraulic pump and there is no hydraulic oil output, it may be that the steering direction of the pump is not correct and the parts are seriously worn or damaged. Replace them in time.
             中科聚峰混凝土搅拌车
  若液压泵有油液输出,查看溢流阀工作是否正常。若不正常,则可能是压力油路中的某个阀有污物或其他原因卡住,处于回油位置,致使压力油路与溢流回路短路,也可能是管接头松脱,或处于压力油路中的某些阀泄漏严重,或液压缸、液压马达的密封损坏,严重泄漏。
  If the hydraulic pump has oil output, check whether the relief valve works normally. If it is abnormal, it may be that a valve in the pressure oil circuit is stuck due to dirt or other reasons, and it is in the oil return position, resulting in a short circuit between the pressure oil circuit and the overflow circuit, or the loose pipe joint, or serious leakage of some valves in the pressure oil circuit, or the seal damage of the hydraulic cylinder and hydraulic horse.
  排除方法:拆开有关阀进行清洗,检查密封间隙的大小及各种密封装置,密封装置损坏应更换。
  Troubleshooting: remove the relevant valve for cleaning, check the size of sealing clearance and various sealing devices, and replace the damaged sealing device.
  若液压泵输出流量随压力升高而显着减小,且压力达不到规定值,则是由于液压泵磨损后间隙增大所致。
  If the output flow of the hydraulic pump decreases significantly with the increase of the pressure, and the pressure can not reach the specified value, it is due to the increase of the clearance after the wear of the hydraulic pump.
  排除方法:测定液压泵的容积效率,即可确定该泵是否能继续使用,对磨损严重的零件,应进行修配或更换。
  Exclusion method: determine the volume efficiency of the hydraulic pump, you can determine whether the pump can continue to use, the parts seriously worn should be repaired or replaced.
  若整个液压系统能建立正常压力,而某些管路或液压缸(或液压马达)中无压力,则可能是由于管路、小孔或节流阀、换向阀等部位堵塞。此时,应逐段检查压力和有无油液通过,找出原因,加以排除。
  If the whole hydraulic system can establish normal pressure, but there is no pressure in some pipelines or hydraulic cylinders (or hydraulic motors), it may be due to blockage of pipelines, orifices, throttle valves and directional valves. At this time, check the pressure and whether there is oil passing through section by section, find out the reason and eliminate it.