搅拌车的制动方式有哪几种？
What are the braking modes of flat mixer?
1.点刹，是很多司机都知道的制动方法，一般在平口搅拌车遇到紧急情况时，猛踩刹车是非常不理智的行为，很容易发生危险的，此时应该先轻点刹车，再放开，再轻点，再放开，让车速逐渐降低，这种方法通常在雨天或冰雪路面上使用，可以防止车辆跑偏或侧滑。
1. Inching braking is a braking method known to many drivers. Generally, when a flat mixer encounters an emergency, it is very irrational to step on the brake violently, which is prone to danger. At this time, you should brake gently, then release, then release, and then release, so as to gradually reduce the speed. This method is usually used on rainy days or ice and snow roads, which can prevent the vehicle from deviation or sideslip.
2.紧急制动，当平口搅拌车在行驶的过程中遇到紧急情况是，驾驶员应迅速放松油门踏板，用力踩下刹车，同时拉紧手刹，尽可能在短距离内将车辆停住，以达到避免事故的目的，这种方法是不得已的情况下采取的紧急措施，因为它对车辆的轮胎和各个部件是有损害的，同时制动时的方向已经不能控制，所以应该尽量避免这种制动。
2. Emergency braking: in case of emergency during the driving of the flat mouth mixer, the driver shall quickly loosen the accelerator pedal, press the brake hard, tighten the hand brake at the same time, and stop the vehicle in a short distance as far as possible to avoid accidents. This method is an emergency measure taken when it is necessary, because it damages the tires and various parts of the vehicle, and the direction of braking can no longer be controlled, Therefore, this kind of braking should be avoided as far as possible.
3.先急后松，这种方法就是在遇到紧急情况时，先急踩刹车接着要缓冲一下再踩刹车，然后根据发生情况点的距离慢慢松开制动踏板，再更换与速度匹配的档位，正常行驶即可。这种方法可以大大降低由车速急剧变化带来的冲击，使车辆运行稳定。平口搅拌车
3. Hurry first and then release. This method is to step on the brake first in case of emergency, then cushion it, then step on the brake, and then slowly release the brake pedal according to the distance from the point of occurrence, and then change the gear matching the speed to drive normally. This method can greatly reduce the impact caused by the sharp change of vehicle speed and make the vehicle run stably. Flat mixer
4.预见性制动，这种方法主要就是在司机开车过程中，对道路上的车辆、行人、非机动车的变化，做预见性的制动，具体做法就是将脚放开油门踏板，利用发动机怠速时的牵阻力作用来降低车速，然后根据具体情况继续减速或者轻踏油门，让车辆平稳的减速或者停车，这种方法能保证行车，降低车辆零部件的损害程度，这种制动方法在平时使用的更多，也更普遍。
4. Predictive braking. This method is mainly to make predictive braking for the changes of vehicles, pedestrians and non motor vehicles on the road when the driver is driving. The specific method is to release the accelerator pedal, use the traction resistance when the engine is idling to reduce the speed, and then continue to slow down or gently step on the accelerator according to the specific situation to make the vehicle slow down or stop smoothly. This method can ensure driving, To reduce the damage of vehicle parts, this braking method is more and more common in peacetime.
The above is about Zhongke Jufeng mixer https://www.cnzkjf.com I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service
