由于自身负载一直都在变化，因此自动上料搅拌机对于轮胎的要求是比较高的。所以做好轮胎的日常维护检查是十分有必要的，下面我们就来具体介绍一下自动上料搅拌机轮胎的维保方法，感兴趣的朋友不要错过。
As the load has been changing, so the requirements of automatic feeding mixer for tires are relatively high. So it is very necessary to do a good job in the daily maintenance and inspection of tires. Now let's introduce the maintenance methods of automatic feeding mixer tires. Interested friends should not miss it.
1、一般情况下，在车轮加载并运行2-5小时后，需要检查车轮上的螺母。交叉拧紧维护手册中显示的扭矩值，如果8小时后螺母仍然拧紧，则检查扭矩间隔长150小时。
1. In general, after the wheel is loaded and operated for 2-5 hours, it is necessary to check the nuts on the wheel. Cross tighten the torque value shown in the maintenance manual. If the nut is still tightened after 8 hours, check the torque interval as long as 150 hours.
2、在保持轮胎适当气压的同时，用阀门检查气压。如果轮胎热时需要充气，则检查同一轴上的另一个车轮，并在低压下充气，使两者保持一致，热的轮子气压需要等于或高于冷的车胎气压，检查车轮损坏情况，检查纹路和移走危险的东西。
2. Check the air pressure with the valve while maintaining the proper air pressure of the tire. If the tire needs to be inflated when it is hot, check the other wheel on the same axle and inflate it under low pressure to keep the two consistent. The pressure of the hot wheel needs to be equal to or higher than that of the cold tire. Check the damage of the wheel, check the grain and remove dangerous things.
3、车轮和轮胎内的气压会引起叉车轮胎部件爆炸，造成较大的人员伤亡，因此在卸下轮胎前应先放掉空气，如果气压低于正确气压的80%，需要在的地方卸下轮胎并充气，并根据轮胎充气部位进行充气，充气时振作起来，使用一个远程气泵，这样人可以远离轮胎。
3. The air pressure in the wheel and tire will cause the explosion of the forklift tire components, causing great casualties. Therefore, the air should be released before unloading the tire. If the air pressure is lower than 80% of the correct air pressure, the tire should be unloaded and inflated in a safe place, and the inflation should be carried out according to the inflation position of the tire. When inflating, cheer up and use a remote air pump, So people can stay away from the tires.
4、检查边缘是否弯曲或损坏。检查是否有丢失或松动的物品，拆下粘在车轮上的金属线，确保车轮紧固，交叉拧紧车轮需要注意，当车轮没有车轮卸载时，它需要给车轮上的螺母上油，在法兰和车轮螺母之间以及螺纹中滴下两滴油。
4. Check the edges for bending or damage. Check whether there are missing or loose items, remove the metal wire stuck on the wheel, ensure that the wheel is tight, cross tighten the wheel. When the wheel is unloaded without wheel, it needs to oil the nut on the wheel, and drop two drops of oil between the flange and the wheel nut and in the thread.
The above is the maintenance method for the tires of automatic feeding mixer introduced by Xiaobian. Tire safety is the premise for the safe production of mixer. It will be difficult to move without tires, so we must maintain the tires. For more information, please click on the official website: Zhongke self feeding mixer https://www.cnzkjf.com 。
