您好,欢迎光临莱州聚峰机械有限公司官方网站! 郑重声明 购机 售后 聚峰官微

全国咨询热线

400-879-1999

您的位置: 首页 > 新闻资讯 > 行业新闻 >
自动上料搅拌机发动机运行错误的含义是什么?
来源:https://www.cnzkjf.com/ 日期:2021-07-07
由于自动上料搅拌机上的某些特定驾驶员不认为发动机温度低,因此发动机恒温器将自动移除,而冷却剂只能从夜间循环中移除。发动机通常在高温条件下运行,因为无法调节冷却强度。这会导致磨损并增加燃油消耗。实际上,高温对发动机有害。为了确保发动机的使用寿命,应将安装了自动饲料混合器的用例限制在环境温度范围内。
Since some specific drivers on the automatic feeding mixer do not think the engine temperature is low, the engine thermostat will be removed automatically and the coolant can only be removed from the night cycle. Engines are usually operated at high temperatures because the cooling intensity cannot be adjusted. This causes wear and increases fuel consumption. In fact, high temperature is harmful to the engine. In order to ensure the service life of the engine, the use case with automatic feed mixer should be limited to the ambient temperature range.
我喜欢橡皮筋。如果皮带太松,皮带不仅会拉伸和损坏,缩短皮带的使用寿命,而且过大的压力会自动加载并扭曲搅拌机的发电机和泵轴,从而损坏中科搅拌机。为了满足技术要求,必 须松开自动饲料搅拌机的风扇皮带。建议的组装偏差为10-15毫米。
I like rubber bands. If the belt is too loose, the belt will not only stretch and damage, shorten the service life of the belt, but also the excessive pressure will automatically load and twist the generator and pump shaft of the mixer, thus damaging the Zhongke mixer. In order to meet the technical requirements, the fan belt of the automatic feed mixer must be loosened. The recommended assembly deviation is 10-15mm.
                    中科搅拌机
许多驾驶员知道这辆车才刚刚起步。同样,如果发动机转速太低,它也不会打滑并可能损坏发动机。
Many drivers know that the car is just starting. Similarly, if the engine speed is too low, it will not slip and may damage the engine.
但是,大多数人都知道,中科搅拌机的油泵由于加热速度慢而无法在短时间内闲置,因此无法快速润滑光滑的表面润滑剂。同时,由于热燃油雾化不足,燃烧的燃油进入曲轴箱,冲刷气缸壁上的油膜并加速零件的磨损。因此,在自润滑发动机启动后的几秒钟的高温条件下,有必要改善怠速加热并提高发动机滑移率。
However, most people know that the oil pump of Zhongke mixer cannot be idle for a short time due to its slow heating speed, so it is unable to quickly lubricate the smooth surface lubricant. At the same time, due to insufficient atomization of hot fuel, the burning fuel enters the crankcase, washes the oil film on the cylinder wall and accelerates the wear of parts. Therefore, it is necessary to improve the idle heating and increase the engine slip rate in the high temperature condition of a few seconds after the start-up of the self-lubricating engine.
这是自动上料搅拌机中使用的发动机不正确的结果,您了解吗?
This is the result of incorrect engine used in automatic feeding mixer, do you understand?